How to set up a record player

Learning how to set up a record player is easier than it looks, and it is worth doing carefully, because a well-set-up deck sounds better and treats records more gently. This guide shows how to set up a record player step by step, from choosing where it goes to balancing the tonearm and connecting the sound. Always follow your own manual where it differs, because every model is a little different.

If you have just been given a turntable, you will need something to play on it. A monthly vinyl subscription sends four secondhand recordings, which can be vinyl, CDs or cassettes, with at least one vinyl record in every box, so there is something new to try as soon as the deck is ready.

How to set up a record player: choose the right spot

Where the turntable sits has a surprisingly large effect on how it sounds and whether it skips. A record player is sensitive to vibration, so give it a firm, level home.

  • Use a solid surface, such as a sturdy shelf or a low unit. Wobbly furniture makes skipping more likely.
  • Keep the deck away from the speakers. Sound from the speakers travels through the furniture and back into the stylus, which can cause a rumbling feedback.
  • Avoid putting it near a heater or in direct sunlight.
  • Make sure there is space around it to lift the dust cover.
  • Place it near a power socket and your amplifier or speakers, so the cables are not strained.
  • Do not stack it on top of an amplifier. Heat can affect the deck, and the electrical hum from some amplifiers can reach the cartridge.

Check that the surface is level with a small spirit level. If it is not, shim the feet or choose a different spot, because a deck that leans can make the tonearm drift.

Fit the platter and belt

Many turntables arrive partly assembled, and it is worth reading the instructions before you start.

How to set up a record player: the first steps

1. Unpack the deck and keep the packaging until you are sure everything works. 2. Remove any transit screws or tonearm clamps. Some turntables have one or more, and leaving them in place will stop the deck working properly. 3. If the platter is separate, place it on the spindle. Many decks have an inner platter and an outer one, so check the order. 4. On a belt-driven deck, loop the belt around the platter and the small motor pulley, following the manual. It should sit flat and not twist. 5. Put the slipmat on top of the platter. 6. Fit the dust cover or its hinges if they come separately.

Handle the belt gently and avoid touching the inside with greasy fingers. A direct-drive deck has no belt, so you can skip that step. If the pieces do not seem to fit, stop and check the manual rather than forcing anything.

Balance the tonearm

The tonearm carries the cartridge and stylus, and it must be balanced so that it applies the right pressure to the record. Many turntables have a counterweight at the back of the arm that is used for this, although some are already set up from the factory.

If your turntable has an adjustable counterweight, the usual sequence is as follows. Check your manual, because the details differ.

1. Remove the stylus guard from the cartridge, carefully, so you do not bend the needle. 2. Release the tonearm from its rest. Hold it so that it cannot swing. 3. Set the tracking force dial and the anti-skate dial, if there are any, to zero. 4. Turn the counterweight until the arm floats level, so that it neither rises nor sinks. You can hold it still and then let go gently to check. 5. Once it balances, turn the tracking force ring, without moving the weight, so that the scale reads zero.

At this point the arm is balanced and the next step is to apply the correct force.

Set tracking force and anti-skate

Tracking force is the downward pressure of the stylus on the record, and it is measured in grams. The right figure depends on the cartridge, so look it up in the cartridge's instructions or the maker's website. Using too little can make the stylus skip and wear records, and using too much can wear the grooves.

Tracking force

Turn the counterweight until the dial shows the recommended weight for your cartridge. If your deck has no dial, a small stylus gauge lets you check the force directly. Do this carefully, because a slip can damage the stylus.

Anti-skate

As a record plays, a slight force pulls the arm towards the centre. Anti-skate counters this. A common starting point is to set it to the same figure as the tracking force, but check your manual, because some decks use a different method. Not all turntables have an adjustable anti-skate, and that is fine.

When you have finished, put the stylus guard back whenever you move the deck.

Connect speakers or an amp

How you connect the sound depends on what you have. The key question is whether your turntable has a built-in phono preamp, because the signal from a cartridge is very quiet and needs boosting before it reaches normal speakers.

  • **Turntable with a built-in preamp:** Use the cable supplied to connect it to powered speakers, or to a normal line input on an amplifier.
  • **Turntable without a preamp:** Connect it to the phono input on an amplifier. If your amplifier does not have a phono input, you will need a separate phono preamp between the deck and the amplifier.
  • **Turntable with a Bluetooth option:** Follow the manual to pair it with a speaker or headphones.
  • **Earth wire:** Some decks have a thin earth lead. Attach it to the earth terminal on the amplifier, which helps to stop humming.

Connect everything with the power off, and turn the volume down before you start. Once it is all connected, switch on, place a record on the platter, set the speed, and lower the stylus carefully. Our guide to the best budget turntable in the UK helps if you are not sure what your deck needs.

Common problems

Most set-up problems are small ones with simple causes.

  • **A humming sound:** Check the earth lead is attached, and move the cables of the turntable away from power cables.
  • **Skipping:** Check that the deck is level, the tracking force is set correctly and the record is clean.
  • **Quiet or thin sound:** You may have connected the deck to a line input without a preamp. Use a phono input or a preamp.
  • **Distorted sound:** The stylus may be worn or dirty, or the tracking force may be wrong.
  • **Wrong speed:** Check the speed selector is on 33 or 45 as the record needs. On a belt-driven deck, a loose or worn belt can also cause speed problems.
  • **The platter does not spin:** Check the belt is in place and that any transit screws have been removed.

Test the set-up with a record you would not mind losing before you play something precious. If anything sounds wrong, stop and work through the list above, because it is easy to damage a record or a stylus by carrying on with a problem. Once everything sounds right, leave the settings alone, and only change them if you replace the cartridge or move the deck.

Keep your records clean, because dirt causes crackle and wears the stylus. Our guide on how to clean vinyl records explains how, and our list of vinyl accessories covers the brushes, mats and gauges that help keep a deck in good order.

Next step

When the deck is playing, keep it busy with a monthly vinyl subscription of secondhand records chosen in your genre.

Subscribe to the mystery music box